Straight into the service manual page
WrenchQuarry
More

Apprentice and trainee pay below journeyman rate: 3 paths

WrenchQuarry Editorial Team · Published · 13 min read · How these guides are written

If you set crew pay on a federal construction job, you have probably heard that apprentices and trainees can be paid less than a journeyman, but only under specific conditions. The rules come from the apprentices and trainees clause in federal contracts, and they are narrower than many owners and team leads assume. Being new, young, or still learning is not enough on its own to justify a lower rate.

Key takeaways

  • Do not assume a lower rate applies because a worker holds a title like apprentice, unless approval is shown.
  • Apprentice pay is a percentage of the journeyman rate, and that percentage comes only from the registered program.
  • Except as 29 CFR 5.16 provides, a trainee is paid below the rate only when individually registered in a program that has received prior approval.
  • If OATELS withdraws approval of a program, the lower rate stops until an acceptable program is approved.

This post walks through the three paths that let a worker earn below the journeyman rate under that clause. For each path, you will see what the worker must have and where the limits are. It is not a replacement for the clause. Read the full text of FAR 52.222-9, Apprentices and Trainees, and check with your contracting officer or your program sponsor when a case is unclear.

Start with the default rule

The starting point matters. Under the clause, a worker may not be paid below the standard rate unless one of the qualifying conditions is met. The trainee provision is direct: trainees will not be permitted to work at less than the predetermined rate for the work performed unless they are employed pursuant to and individually registered in a program which has received prior approval. The clause also points to the exception in 29 CFR 5.16, so check that section if you think it might fit your situation.

In plain terms, a lower rate is an exception you must be able to justify. Before you set a lower rate, confirm three things: the worker's status, the approval of the program behind that status, and the classification of the work the worker is actually doing.

Federal clauses are not the only minimums on a job. State law can set its own floors, and the rules differ from place to place. Ohio's revised code, for example, provides that a minimum rate of wages for common laborers, on work coming under the jurisdiction of the department of transportation, shall be fixed in each county of the state. A state rate like this may apply alongside the federal clause. Check both before you set crew pay, and ask the agency that administers the job which rules it enforces. For the timing of wage changes on public bids, see public bid wage changes.

A useful habit is to write down, for each worker on a lower rate, which path applies and where the proof is kept. That note turns a general sense that someone is an apprentice into a record you can check. For keeping those notes together, see job file closeout.

Each path below depends on approval. The clause refers to approval by OATELS, the federal body named in the clause, or by a State Apprenticeship Agency where that is appropriate. If you cannot show the approval, you cannot rely on the lower rate.

Path 1: Registered apprentices in an approved program

The first path covers apprentices working under a registered apprenticeship program. This is the most familiar path, and most crews are set up around it. The worker is enrolled in an approved program, and the program sets the ratio of apprentices to journeymen and the wage progression for each apprentice.

The ratio is the first limit. The allowable ratio of apprentices to journeymen on the job site in any craft classification shall not be greater than the ratio permitted to the Contractor as to the entire work force under the registered program. You cannot staff a craft with more apprentices than the registered program allows, even if the company as a whole has enough journeymen. The ratio is measured against the craft on the job site, not against the whole company.

The wage is the second part. Pay is set by ratios and wage rates (expressed in percentages of the journeyman's hourly rate) specified in the Contractor's or subcontractor's registered program. In practice, your apprentice's pay is a percentage of the journeyman rate, and that percentage comes from the registered program, not from a number you pick for the crew. If the program raises the percentage as the apprentice moves through the stages, the apprentice's pay should rise with it.

Fringe benefits are the third part. Apprentices shall be paid fringe benefits in accordance with the provisions of the apprenticeship program. A lower hourly wage does not excuse you from the benefit side. Check what the program requires and handle the apprentice's benefits the way the program describes.

Location matters too. Where a Contractor is performing construction on a project in a locality other than that in which its program is registered, the ratios and wage rates (expressed in percentages of the journeyman's hourly rate) specified in the Contractor's or subcontractor's registered program shall be observed. Moving a crew to a new job site does not reset the program's rules.

Path 2: Trainees in an approved training program

The second path covers trainees. A trainee is not the same as an apprentice under this clause, and the two words should not be used interchangeably. The clause treats trainees under its own rules, and those rules are strict about registration.

The key requirement is individual registration. Except as 29 CFR 5.16 provides, trainees are paid below the rate only if they are employed pursuant to and individually registered in a program which has received prior approval. The word individually matters. It is not enough that your company has an approved training program somewhere in its files. Each trainee has to be registered in that program, and you should be able to show it.

Once a trainee is properly registered, the pay rule is tied to progress. Every trainee must be paid at not less than the rate specified in the approved program for the trainee's level of progress, expressed as a percentage of the journeyman hourly rate specified in the applicable wage determination. Two things follow. The trainee's rate depends on the level of progress the program records for that person, so a trainee who has advanced should not be held at the entry rate. The percentage applies to the journeyman hourly rate in the applicable wage determination.

Trainees carry a withdrawal risk. In the event OATELS withdraws approval of a training program, the Contractor will no longer be permitted to utilize trainees at less than the applicable predetermined rate for the work performed until an acceptable program is approved. If approval is pulled, the lower trainee rate goes away with it. Track the status of the program, not just the trainee's name on a list.

Path 3: Probationary apprentices in their first 90 days

The third path is the one most often misunderstood. It allows a worker to be employed as a probationary apprentice without individual registration, but only for a limited period and only under certain conditions.

The allowance covers the first 90 days of probationary employment as an apprentice in such an apprenticeship program, even though not individually registered in the program, if certified by the OATELS or a State Apprenticeship Agency (where appropriate) to be eligible for probationary employment as an apprentice. Both conditions must be true. The first is the time limit: the allowance covers the first 90 days of probationary employment, not the whole period a worker stays on the job. The second is certification: the worker must be certified as eligible for probationary employment by the approving body the clause names.

Do not treat the 90 days as a grace period you can extend by moving the worker to a new start date. The allowance is tied to probationary employment in the program. If the worker is still on an apprentice rate after the allowance has run out, and is not registered or otherwise employed in a way the clause recognizes, the rule for unregistered workers applies. That rule is covered in the next section.

For team leads, the practical question is simple. For each probationary apprentice, you should know the date the probation started, the date the 90-day window ends, and where the certification is kept. If you cannot answer those three questions, that worker should not be on the lower rate.

What does not qualify for a lower rate

Many pay problems on federal jobs come from workers who fit none of the three paths but are still paid as though they do. The common patterns are worth avoiding.

First, a worker does not qualify just because the payroll says apprentice. The clause addresses this directly: any worker listed on a payroll at an apprentice wage rate, who is not registered or otherwise employed as stated in paragraph (a)(1) of this clause, shall be paid not less than the applicable wage determination for the classification of work actually performed. The label on the payroll does not decide the rate. The registration or qualifying employment does.

Second, the classification of the work matters, and the wage determination is the place to start. For a California project, the Department of Industrial Relations says to first examine if your craft's determination is among the basic trades that apply to most counties in California. That check comes before any question about a lower apprentice rate. Review the actual duties of each worker against the determination, not only the job title.

Third, being new is not a path on its own. A worker who is new to your company, the trade, or the job site does not earn a lower rate by that fact alone. Only the three paths above provide that treatment, and each requires specific documentation.

Fourth, do not assume a training arrangement covers a worker who is not individually registered. The clause requires individual registration for trainees. A general statement that the company trains people is not enough.

Fifth, a reassigned worker needs a fresh review. The ratio and wage rules are tied to the craft classification and the work actually performed. If an apprentice moves to a different craft or takes on different duties, the pay question has to be answered again for the new assignment.

Ratios and fringe benefits on the job

Once you know which path applies, the day-to-day work is keeping the crew within the rules. The ratio matters most on a busy site. A crew that looks balanced across the whole company can still be out of ratio on a single job, if one craft has too many apprentices for its journeymen. Check the ratio craft by craft every time the crew changes.

Plan the ratio before the work starts, not after the crew arrives. Adding one apprentice to a small craft can put that craft out of ratio on a particular job. Start from the number of journeymen in each craft on that job, apply the ratio from your registered program, and confirm the count each time someone is added or pulled off the site.

Fringe benefits need the same attention. Because they follow the apprenticeship program, the amounts and the way they are paid should match what the program describes. If a worker is paid a lower wage but the benefit side is handled as an afterthought, review it before a payroll audit does it for you.

When approval is withdrawn

Approval can be withdrawn, and when it is, the lower rate can stop applying. For apprentice programs, in the event OATELS, or a State Apprenticeship Agency recognized by OATELS, withdraws approval of an apprenticeship program, the Contractor will no longer be permitted to utilize apprentices at less than the applicable predetermined rate for the work performed until an acceptable program is approved. The trainee rule works the same way, as quoted earlier.

This is why approval is more than paperwork. The lower rate depends on a program that remains approved while the work is being done. Find a way to learn when approval changes, whether that means asking your program sponsor to notify you, checking status on a regular schedule, or building the check into your payroll review. The quoted text does not give a grace period, so do not plan on one. Verify approval before you pay the lower rate for each pay period.

If approval is withdrawn, do not simply relabel the worker in your records. Plan the payroll change in advance so it does not surprise your budget or your crew, and tell the affected workers what their rate will be before the first pay period under the new status.

A practical checklist for owners and team leads

Use this list before you set crew pay on a federal job that includes the apprentices and trainees clause. It turns the rules above into questions you can answer with records.

  • Confirm the contract includes the clause and read the full text, not only the summary in this post.
  • For each apprentice, confirm the individual registration and the approved program that covers it.
  • For each trainee, confirm individual registration in an approved training program and the level of progress recorded by that program.
  • For each probationary apprentice, record the start date of the probation, the date the 90-day window ends, and the certification that the worker is eligible for probationary employment.
  • For any worker not covered by one of those records, pay the wage determination rate for the work actually performed.
  • Check the apprentice-to-journeyman ratio craft by craft on each job site, using the ratio from the registered program.
  • Set each apprentice's and trainee's wage as the percentage the program specifies.
  • Confirm that fringe benefits follow the apprenticeship program's provisions.
  • Confirm that the ratios and wage percentages from your registered program are applied on any job site outside the program's home locality.
  • Check whether any state minimum for the work also applies.
  • Monitor the approval status of each program, and be ready to change pay if approval is withdrawn.
  • Keep the records together so you can show them to a reviewer without rebuilding the file from memory.

Closing thoughts

The three paths are the main ways the clause lets a worker earn below the journeyman rate: as a registered apprentice in an approved program, as an individually registered trainee in an approved training program, or as a probationary apprentice within the first 90 days who is certified eligible. Each path has its own limits, and each depends on approval that can change. The clause also refers to the exception in 29 CFR 5.16, which this post does not cover, so check that section separately. Outside those paths and that exception, a worker is paid the rate for the work actually performed.

The safest approach is to base pay decisions on documents, not job titles. Know which path each worker is on, keep the records that prove it, and review the status of your programs regularly. If something is unclear, go back to the clause text and ask the people who administer your contract before you pay the lower rate. A short conversation at the start of a job costs far less than correcting pay after the fact.

Your next step today: pick one worker on a lower rate and check that the registration or certification, and the program's approval, are on record. If either is missing, the clause points to the wage determination for the work actually performed.

Frequently asked questions

Can a probationary apprentice earn below journeyman rate?

Yes, but only for the first 90 days of probationary employment, and only if OATELS or a State Apprenticeship Agency (where appropriate) certifies the worker as eligible for probationary employment as an apprentice.

Does an apprentice job title alone justify a lower rate?

No. The payroll label does not decide the rate; registration or qualifying employment does.

What happens if approval is withdrawn?

The lower rate stops until an acceptable program is approved, and the quoted clause text gives no grace period.

Sources

More field guides