Straight into the service manual page
WrenchQuarry
More

California hazardous chemicals: 3 sources to check

WrenchQuarry Editorial Team · Published · 12 min read · How these guides are written

Under California's hazard communication rule, a chemical listed on one of the named sources is treated as hazardous.

Key takeaways

  • Check the chemical names in each product, not only the label or the marketing copy.
  • Treat a chemical listed on a named source as hazardous under the rule.
  • Write down the exact chemical name and the source you checked.
  • Mark anything you cannot resolve and send it to the supplier or a qualified person.

Why the label is not the whole answer

Field-service crews carry a lot of products, and each one comes with a label. Many owners treat that label as the final word on whether a product is dangerous. It is a useful starting point, but it does not settle the question on its own. The named sources look at the chemicals inside a product, not only at the words printed on the outside of the container. For the label side of that check, see Chemical labels: 6 items to check before dispatch.

The rule is California Code of Regulations, Title 8, Section 5194. You can read the text at the Department of Industrial Relations page for Section 5194. It is written for manufacturers, importers, and employers who classify chemicals. A small firm that buys products and uses them on jobs is often in the position of an employer who has to understand that classification, even when a supplier did the original work.

This post covers three of the sources the rule names. It explains what each one is, how to check a product against it, and how to keep a record of what you decided. It also gives a sorting routine you can run on a van or in a shop. Nothing here replaces the full text of the rule. Where the rule itself gives a number or a date, check the original page before you act on it.

Source one: the list of hazardous substances

The rule tells manufacturers, importers, and employers who classify chemicals to treat certain listed chemicals as hazardous. The first source on that list is "the list of hazardous substances prepared by the Director pursuant to Labor Code section 6382 and as promulgated in title 8, California Code of Regulations, section 339" (DIR, Section 5194).

In practice, this means a chemical that appears on that list is treated as hazardous for the purposes of the rule, even if the product's packaging does not say so. The list works on chemicals, not on brand names. A cleaner, a degreaser, and a spray adhesive can be sold under different names and still contain the same listed chemical. The check therefore has to start from the ingredient, not from the marketing copy on the front of the can.

For a van or a shop, the routine is simple to describe and slower to carry out. Pick up each container, find the chemical names in its ingredient information, and compare each name against the list. If a name matches, treat the product as hazardous under this rule and record the match. If a name does not match, that does not close the question, because the product may still be covered by another source the rule names.

Watch for product names that look alike. Two items on a shelf can share a family name and differ by one ingredient. A short name such as "solvent" or "cleaner" tells you almost nothing about what is inside. Write down the exact chemical name as the label or the supplier's information gives it, and keep that name with the product record. If you later need to explain a decision, the exact name is what someone will want to see.

Once a chemical is treated as hazardous, the rule says how to classify it. Appendix A is consulted for the classification of health hazards, and Appendix B is consulted for the classification of physical hazards. The rule also says that a listed chemical is classified using the criteria described in Appendix A. Your supplier or a qualified person may do the classifying for you, but a field team should know that the appendices exist and where they are. When a supplier sends a classification, ask which appendix it used, so the answer can be checked against the rule's own references.

Source two: the federal toxic and hazardous substances subpart

The second source is "29 CFR part 1910, subpart Z, Toxic and Hazardous Substances, Occupational Safety and Health Administration (OSHA)" (DIR, Section 5194). This is a federal set of rules, but California's section points to it directly. A California check can therefore lead you to a federal list. Do not skip this source because it sounds like it belongs to another government.

For a small firm, the practical step matches the state list. Check each product's chemicals against this subpart. A chemical listed there is treated as hazardous under the California rule, and it is classified with the same Appendix A criteria as any other listed chemical. Read the subpart itself rather than relying on a summary, since the wording of a listing matters when you are deciding whether a match is real.

Work through the subpart by chemical name, not by product type. A product type such as "roof sealant" or "pipe cleaner" does not tell you whether it is covered. The chemicals inside it do. The same chemical can also appear under more than one name, including a common name and a formal name. When a match is unclear, record the name you found and the name you were checking against, and mark the item for review instead of guessing.

It is worth saying this out loud to your team. A California rule can point to federal sources, so a federal list still matters for a California check. Crew members who have worked for other employers may assume a product is fine because it passed some other check. A short reminder at the start of a job, that this source counts here too, keeps that assumption out of your records.

Mixed products deserve extra care. A single product can contain several chemicals, and each one has to be checked on its own. One chemical that matches is enough to make the product count under this source, so do not stop after the first ingredient that looks harmless.

Source three: the Title 8 articles on dusts and fumes

The third source is a set of California articles. The rule names "Chemicals specifically identified and regulated under Title 8, Article 107, Dusts, Fumes, Mists, Vapors and Gases, and Article 109, Hazardous Substances and Processes" (DIR, Section 5194).

The key phrase is "specifically identified and regulated." A chemical falls under this source when one of those articles names it and regulates it. A general idea that a product is a gas, a fume, or a dust is not the same test. Read the article for the specific chemical, and note whether the article regulates it in a way that applies to the work your crew does.

This source differs from the first two in one respect. It asks whether an article identifies the chemical by name, rather than whether a list or subpart includes it. Because Article 109 covers processes as well as substances, the question is not only about the container. Think about what the crew does with the product. If the job involves spraying, sanding, heating, or mixing, the way the product is used may matter as much as what it is called.

The table below compares the three sources side by side.

Source named in Section 5194What the rule saysWhat to check on your van or in your shop
List of hazardous substances (Labor Code section 6382; title 8, section 339)Listed chemicals are treated as hazardous and classified using Appendix ACompare each product's chemical names to the list
29 CFR part 1910, subpart Z (OSHA)Listed chemicals are treated as hazardous and classified using Appendix ACompare each product's chemical names to the federal subpart
Title 8, Article 107 and Article 109Chemicals specifically identified and regulated in these articles are coveredCheck whether any chemical is named and regulated in these articles

Keep a record of how you decided

The rule also says something about the paper trail. It requires documenting "the basis for that determination including the studies or evidence relied upon," and making that documentation available to employees, employers, and the Division on request (DIR, Section 5194). The rule ties this duty to its other sections as well, so a record that is complete on its own terms is the safest approach.

For a small firm, a practical habit is to write down which source you checked, which chemical you matched, and what evidence you used each time you decide whether a product is hazardous. A shared sheet works well for this. Each row can hold the product name, the chemical name as written, the source you checked, the outcome, and a short note on the evidence. Keep the outcome short, such as "listed, treated as hazardous" or "no match found, marked for review." The point is that the record exists before anyone asks for it.

A record also helps when the team changes. A dispatcher who takes over the list can see what was decided, on what basis, and what is still open, instead of starting from scratch. It also helps when a supplier changes a formula, because you can compare the new ingredient names against the entries you already made.

Store the record where the whole team can reach it, and make sure the person who keeps it knows the routine. A record that only one person understands is hard to defend.

Trade secrets and withheld names

Some ingredients may be claimed as trade secrets. The rule says that "Appendix E to section 5194-Definition of Trade Secret sets out the criteria to be used in evaluating trade secrets" (DIR, Section 5194). The criteria are in the appendix, so read them rather than relying on a supplier's word that an ingredient is protected.

If a supplier withholds an ingredient name, check Appendix E before you decide the matter is closed. Ask the supplier in writing what the claim is based on, and record the answer. A withheld ingredient still needs a decision. The entry in your record should say that the name was withheld, that the claim was checked against Appendix E, and what you concluded. Leaving the entry blank is the one choice that does not work.

Common mistakes to avoid

Several mistakes come up again and again with small crews. The first is treating the label as the answer. A label can be incomplete, and it can use a marketing name that tells you nothing about the chemicals. The second is checking only one source. Each of the three sources in this post can apply on its own, so a product that clears one may still need checking against the others.

The third mistake is assuming a small container is safe. The fourth is forgetting the truck cab, the spare can under the seat, and the cleaning supplies in the back room. Those items are often the ones nobody has written down. The fifth is failing to recheck after a change. A new supplier, a new formula, or a new job type can change what is on the van, and the routine has to run again.

The last mistake is leaving open items open for too long. A flagged product should have a named person responsible for resolving it, and a date by which the team reviews it. That keeps the list honest.

A simple sorting routine

A workable method for a van or a shop is a short series of steps:

  1. List every product on the van and in the shop, including cleaners, solvents, and adhesives you keep on hand.
  2. Write down the chemical names for each product, not just the brand name.
  3. Check each chemical against the three sources in this post: the list of hazardous substances, the federal subpart, and the California Title 8 articles.
  4. Note which source you checked and what you found for each chemical.
  5. Mark anything you cannot resolve, and send it to the supplier or a qualified person.

Repeat the routine once when you start, and then again whenever you add a product. A product that comes from a crew member's own supply should go through the same routine before it goes on the van. When a product is replaced with a new version, treat the new version as a new item and check its ingredients. For shop storage, see Flammable storage: 5 checks before you stock the shop.

The routine works best when each step has a clear owner. The next section describes one way to divide the work.

Who does what on a small team

Owners set the standard for the firm. They decide that nothing goes on a van or into a shop without a check, and they make sure the record is kept. Dispatchers often see orders and restocks first, so they are well placed to flag new products before they reach a crew. Team leads review flagged items and answer questions from crew members. Crew members report anything they do not recognize and do not decide the matter on their own.

Write these roles down. A written list of who does what means a missing person does not become a missing check. If a dispatcher is out for a week, the team lead knows to hold new products until the check is done. If a team lead leaves, the owner knows who takes over the review. For the handoff side of this, see Field Service Work Order Checklist for Dispatch Handoffs.

Keep the process short enough that people will actually use it. A checklist on a clipboard in the van is more useful than a long manual nobody opens.

Where to start this week

Start with the products that get used most often, because those are the ones most likely to reach a crew member's hands. Today, pick one van or one shop area, run the routine from start to finish, and time how long it takes. Use what you learn to plan the rest of the fleet.

Work through the three sources, keep your notes, and make sure everyone on the team knows where the list lives. The aim is not perfection on day one. The aim is a clear record that shows your firm checked, and a routine that keeps that list current as products change.

Frequently asked questions

Where can I read the rule itself?

The text is on the Department of Industrial Relations page for Section 5194, linked near the top of this post.

Who should keep the record?

One named person should keep it, and that person should know the routine.

Sources

More field guides