- Use +37°C (98.6°F) as the core reference on every crew sheet, and write both scales so every reader compares the same number. Every other figure in the briefing is easier to judge once it is measured against that reference.
- Cold exposure begins when the body loses heat faster than it can produce it. A core below 37°C follows when heat loss exceeds what production and retention can generate, so plan around that imbalance rather than waiting for a single alarming reading.
- Wind adds to the loss side of that balance. It draws heat from the body, lowers skin temperature first, and eventually lowers internal body temperature, which makes exposed skin an early signal for the crew.
- Conductive heat loss, the heat that moves through direct contact, is generally only about 2% of overall loss. Contact surfaces are therefore a small share of the total, and the briefing should focus on whole-body loss.
- The CCOHS cold working page uses the kilocalorie as its heat unit, one being the amount needed to raise 1 kilogram of water by 1°C. Use that same unit when comparing energy figures across plans so the numbers stay consistent from one briefing to the next.
The body-temperature basis for a crew briefing is a core temperature of +37°C (98.6°F), and the core drops below that when the body loses more heat than it can produce and retain. The two heat-loss facts to brief are that conductive loss through direct contact accounts for only about 2% of overall loss, and that wind draws heat from the body, lowering skin temperature and eventually internal temperature.
Net takeaways
Where the 37°C core figure comes from
Every briefing on cold or hot outdoor work needs one reference point, and the Canadian Centre for Occupational Health and Safety gives it in plain terms: your body's core temperature is +37°C, or 98.6°F. The CCOHS page on cold health effects and first aid states that figure while explaining what drives heat loss. That placement matters, because it turns the number from a fact about physiology into something a planner can use on site.
The same passage identifies the comparison that matters. In the case it describes, the operative factor is the difference between the temperature of the air and the temperature of the body. The air reading is what your crew sees on the thermometer, and the body side of that comparison is the 37°C core. Put together, the air reading and the core reference give you a gap, and the size of that gap is the basic quantity behind cold-exposure decisions on a work site.
Write both scales on the sheet. Crews and supervisors do not always read the same units, and the source gives the core figure in Celsius and Fahrenheit. Printing +37°C beside 98.6°F removes any argument about whether a reading is high or low, and it lets a worker who thinks in Fahrenheit check the same reference a supervisor reads in Celsius.
Treat the 37°C figure as the starting point of the briefing. The sections that follow show what moves the body away from it, beginning with the balance between heat lost and heat produced.
Cold exposure starts as a heat deficit
Cold stress is easiest to plan for when you think of it as a balance problem rather than a single temperature reading. The NIOSH guidance on outdoor cold-weather work, archived by the CDC, states the mechanism in one sentence: when exposed to cold temperatures, the body begins to lose heat faster than it can be produced. That sentence describes a deficit. The body is not failing at one moment; it is spending heat faster than it generates it.
The CCOHS health effects page defines the threshold. When more heat is lost than the combined heat production processes and heat retention mechanisms can generate, the core body temperature drops below 37°C. The table below sets out the three states a planner should be able to name on site.
| Heat balance state | What the body is doing | Core temperature |
|---|---|---|
| Early cold exposure | Losing heat faster than it is produced | Not yet below 37°C |
| Loss exceeds production and retention | Generation and retention cannot keep pace with loss | Drops below 37°C |
| Balanced | Losses are matched by production and retention | Not dropped below 37°C |
The table shows why the briefing should track two things at once. The first is how much heat the body makes and keeps. The second is how fast it is losing heat. A crew can be in the early stage for some time before the core moves, so the early state is the one to watch. Once loss clearly exceeds the body's combined production and retention, the core is already falling below its reference, and the response has to match that stage.
How wind speeds up body cooling
The National Weather Service's wind chill guidance explains the mechanism in a single sentence: as the wind increases, it draws heat from the body, driving down skin temperature and eventually the internal body temperature. The sentence sets out an order of effects. Wind acts on the surface first, and the effect reaches the core later. The sequence is set out below.
| Step | What wind does | What the crew sees |
|---|---|---|
| 1 | Draws heat from the body | Heat leaves faster than before |
| 2 | Drives down skin temperature | Exposed skin cools first |
| 3 | Eventually lowers internal body temperature | Core temperature falls after the surface |
That order is useful for planning. Exposed skin cools before the core moves, so the surface change is the earlier signal. A crew that treats skin cooling as a warning has time to act before the core is affected. The timing is also why the wind belongs on the loss side of the balance described in the previous section. Wind does not replace the body's production of heat; it adds to the heat leaving the body, which widens the gap between loss and production and retention.
The practical point for a briefing is to name wind as a driver of loss, not as a background detail. When the wind rises, the balance tilts toward loss, and the team should expect the same body to be working against a larger deficit than it was at calmer conditions. Keep the step order in mind when you describe symptoms: surface effects first, core effects after.
Conduction's small share of total loss
The CCOHS health effects page gives the share that conduction contributes: generally, conductive heat loss accounts for only about 2% of overall loss. Conduction is heat moving from the body into whatever it touches directly. The word "generally" marks this as a typical share, not a fixed rule for every task or setting, but the figure is still a clear signal about where most heat does not leave.
The table below puts the figures side by side so the team can see the scale of the contact share against the core reference.
| Measure | Figure |
|---|---|
| Conductive heat loss, share of overall loss | About 2% |
| Reference core temperature | +37°C (98.6°F) |
| Difference the source names as the operative factor | Air temperature and body temperature |
The small share has a direct planning consequence. If conduction were the main route of loss, a briefing could focus mainly on contact points such as seats, floors, and handled objects. The 2% figure shows that contact is a minor route in the general case. A briefing built only around contact surfaces would leave out almost all of the loss the body actually experiences.
So the briefing should frame the work around whole-body loss. The air-to-body difference, the balance between production and loss, and the wind all act on the body as a whole. Contact surfaces still deserve attention in the sense of avoiding avoidable cold contact, but they should be presented as a small part of the picture, not as the main driver of cooling.
Measuring heat in kilocalories
When a briefing needs to describe heat as a quantity, the CCOHS cold working page gives the unit the source uses: one kilocalorie is the amount of heat needed to raise the temperature of one kilogram of water by 1°C. The definition is short, but it sets the scale for any heat figure a planner brings into a plan.
| Element of the definition | Figure |
|---|---|
| Mass of water warmed | 1 kilogram |
| Temperature rise | 1°C |
| Heat unit | 1 kilocalorie |
The definition gives a fixed reference. A planner can read any heat figure in kilocalories and know exactly what it means: the heat that would raise 1 kilogram of water by 1°C. Without a stated unit, a heat number on a sheet can be misread, and a team may compare figures that were measured in different terms. Using the kilocalorie as the common unit keeps the comparison honest.
The unit also works best when it is used consistently. Once a plan states a heat figure in kilocalories, every later comparison should use the same unit, and the briefing should avoid switching between units halfway through. Consistency is what lets a supervisor check one plan against another without converting numbers, and it keeps the heat discussion tied to the same balance of loss and production described earlier.
Cold and heat planning side by side
Cold and heat stress are often briefed as opposites, but the sources treat them differently, and a crew sheet should show that difference. For cold, the NIOSH guidance on outdoor cold-weather work, archived by the CDC, describes a body that begins losing heat faster than it can produce it. The planning question for cold is the balance between loss and production. Wind enters that same balance. The National Weather Service wind chill guidance says wind draws heat from the body and drives down skin temperature before it reaches the core.
The table sets the two sides against the same planning factors. It is a briefing aid, not a full risk assessment, and the heat column rests on the source discussed in the next section.
| Planning factor | Cold exposure | Heat exposure |
|---|---|---|
| What the body is doing | Losing heat faster than it is produced | Core temperature can rise during strenuous work |
| Early signal named in the sources | Exposed skin cools before the core | Caution: sweating is not a sign of coping |
| Accelerating factor named in the sources | Wind draws heat from the body | Strenuous exercise or work |
The side-by-side view matters because the cold column gives the crew a physical mechanism to watch. Skin cooling is a visible, early change, and wind is a factor the supervisor can check at the start of a shift. The heat column is harder to read. Sweating, which many crews use as a rough indicator that the body is coping, is not a reliable sign in the way cold-side skin cooling is. A briefing that treats both hazards the same way will miss this difference.
Keep the two sections on separate lines of the sheet, each with its own early signal. Crews who see cold and heat listed side by side are less likely to assume that one set of warning signs covers both.
Why sweating can mislead on heat stress
It is tempting to read sweat as proof that a worker is handling heat, but the CCOHS humidex guidance on heat stress warns that sweating alone does not show the body is coping. The reason is that there are two types of heat stroke, and they look different. The source describes "classical" heat stroke as occurring with little or no sweating, and it notes that this type usually affects children, persons who are chronically ill, and the elderly. "Exertional" heat stroke is different: the body temperature rises because of strenuous exercise or work, and sweating is usually present.
The table sets the two types side by side so the briefing can name what each one looks like.
| Type | Sweating | Who it usually occurs in | What drives the rise |
|---|---|---|---|
| Classical | Little or no sweating | Children, chronically ill persons, the elderly | Not tied to work in the source |
| Exertional | Usually present | Not specified by the source | Strenuous exercise or work |
The practical lesson is that a crew can be sweating and still be at risk. Exertional heat stroke is the type that matches active crew work, and it comes with sweating. A supervisor who relies on dry skin as the warning sign would miss it entirely. The briefing should therefore tell crews that sweat is not a reassurance and that the rise in body temperature is the concern, whatever the skin looks like.
The source does not give thresholds for when to stop work, and this section does not invent them. Its value is in correcting a common assumption: sweating does not prove the body is in control of heat.
What a core drop below 37°C means
The core reference of 37°C is only useful if the team knows what happens when the core moves away from it. The CCOHS health effects page gives the mechanism: when more heat is lost than the combined heat production processes and heat retention mechanisms can generate, the core body temperature drops below 37°C. A core drop, in other words, is a sign that the balance has already tipped. The loss has outrun the body's ability to replace it and keep it in.
This matters for timing. The wind guidance describes surface cooling first and internal cooling eventually, so the core drop comes after the early signs. By the time a crew member's core is measurably below the reference, the warning has already passed. The briefing should therefore not treat a core reading as the first alert. It should treat it as confirmation that earlier signs were missed or ignored.
The source does not specify the core temperature at which a crew must stop work, nor does it set a number for how far below 37°C is acceptable. Those decisions belong to the site's own medical and safety procedures, and the briefing should point to them rather than improvise a threshold. What the team can state with confidence is the direction of the change. Below 37°C means heat loss has exceeded what the body can generate and retain.
Where the exposure limit basis comes from
Team leads often ask where the numbers in a cold-work briefing come from, and the CCOHS cold working page gives a direct answer for its material. The page carries a source note stating that it is adapted from the Threshold Limit Values (TLV) and Biological Exposure Indices (BEI) booklet, published by ACGIH in Cincinnati, Ohio, in 2024, on page 226. That note is the attribution the page itself gives, and the briefing should carry it forward in the same form.
The attribution tells a reader where the guidance originates and which version of the booklet it reflects. A supervisor who needs to check the basis for a briefing can go to the named booklet and page rather than relying on memory or a secondhand summary. That is the main value of recording the source line on the sheet.
The excerpt used for this briefing does not reproduce any limit values from the ACGIH booklet, so the briefing should not state any. Quoting a specific exposure figure from memory would claim more than the source supports. The safe approach is to name the attribution, note that the page is adapted from the 2024 booklet, and leave any numeric limit to be taken from that booklet directly.
Which one should you pick?
When a supervisor has to choose what to watch first, the sources point toward the earliest reliable signal. The National Weather Service describes wind drawing heat from the body and driving down skin temperature before it eventually lowers internal temperature. The NIOSH guidance, archived by the CDC, describes the body losing heat faster than it can produce it. Together, these point to a clear choice between two options.
| Option | What it tracks | When it reacts |
|---|---|---|
| Skin cooling and wind exposure | Surface temperature and the wind acting on it | Early, before the core moves |
| Core temperature alone | Internal body temperature | Later, after the surface has cooled |
The better choice for the briefing is the first option. Skin cooling and wind exposure give the crew time to act while the body is still in the early stage of heat loss. Waiting for a core change means waiting for the balance to tip, which the CCOHS health page describes as the point when loss exceeds production and retention.
Keep the core reference in the brief anyway. The +37°C (98.6°F) figure is the reference the core reading is judged against, so it shows how far the body has moved from normal. The pick is about which signal triggers action, not which number is worth knowing. For cold work, pick the surface and wind signal as the trigger, and use the core as the reference that gives those signals their meaning.
Related guides: Boiler water: 2 temperature checks and safety terms · California outdoor heat rules: 3 duties for crews · 3 safety rules that still apply after a heat exemption.
Reader questions
What temperature should the briefing use as the core reference? The CCOHS health page gives the core body temperature as +37°C, or 98.6°F. Write both on the sheet so every reader compares the same figure.
Does wind matter if the air temperature is not extreme? The National Weather Service says wind draws heat from the body as it increases, driving down skin temperature and eventually internal temperature. The sources tie wind to heat loss, so it belongs in the briefing whatever the thermometer reads.
Is contact with cold surfaces the main way the body loses heat? No. The CCOHS health page says conductive heat loss generally accounts for only about 2% of overall loss, so the briefing should focus on whole-body loss.
Why is sweating not a reliable sign in heat work? The CCOHS humidex guidance cautions that sweating alone does not show the body is coping with heat. Exertional heat stroke usually comes with sweating, so a sweating worker can still be at risk.
What happens when the core temperature falls? According to the NIOSH guidance, archived by the CDC, the body begins to lose heat faster than it can be produced.
What unit should the briefing use for heat figures? The CCOHS cold working page defines one kilocalorie as the heat needed to raise 1 kilogram of water by 1°C. Use kilocalories consistently across the plan.
Does the source give a limit value for exposure? The CCOHS cold working page credits an ACGIH booklet, published in 2024 and cited at page 226. The excerpt used here does not list any limit values, so take any numeric limit directly from that booklet rather than from this briefing.