Straight into the service manual page
WrenchQuarry
More

2 install mistakes that can cut efficiency by up to 30%

WrenchQuarry Editorial Team · Published · 16 min read · How these guides are written

ENERGY STAR reports that improper installation can reduce system efficiency by up to 30 percent, and that poorly sealed duct systems can result in up to a 30% loss in efficiency (ENERGY STAR). The two install mistakes this post covers are a filter rating the system was not designed for and a duct system that is not well sealed.

Net takeaways

  • Improper installation can reduce system efficiency by up to 30 percent, according to ENERGY STAR, so treat install quality as a sign-off item.
  • Poorly sealed duct systems can result in up to a 30% loss in efficiency, according to ENERGY STAR, so verify sealing before the walls close.
  • Many existing HVAC systems were designed and installed to use MERV 6 to MERV 8 filters, according to AHRI, so check the design before upgrading a filter.
  • ASHRAE recommends MERV 13 at minimum and preferably MERV 14 or better, according to AHRI, but the higher efficiency comes with a penalty.

Why the 30 percent figure matters to your installs

Dispatchers and team leads spend most of their day on schedules, parts, and customer handoffs, so an efficiency number can look like a problem for someone else. Sign-off is the last point where a poor install gets caught before the customer lives with it. The cost of a missed problem lands on the homeowner's utility bill, and the homeowner is the person who will call the company when it happens.

ENERGY STAR gives the household side of the picture. The average household spends about $1,900 a year on energy bills, with nearly half going to heating and cooling (ENERGY STAR). That heating and cooling share is the portion an install touches most directly, so small losses there add up on a bill the customer reads every month.

The same source links the loss to the installation itself. It states that improper installation can reduce system efficiency by up to 30 percent, costing more on utility bills and possibly shortening the equipment's life (ENERGY STAR). Two points in that sentence matter at sign-off. First, the loss is tied to how the job was done, not only to the model number on the unit. Second, there is a cost beyond the bill, which is a possibly shorter equipment life. A customer who is told the system works, then faces higher bills and a shorter run from the equipment, will remember who signed off.

For a team lead, this turns a general quality concern into a checkable item. The question at sign-off is not only whether the unit runs. It is whether the installation matches the design and sealing that the sources tie to efficiency. The next sections cover two mistakes that the sources connect to efficiency losses, and what to require before the paperwork goes to the customer.

Mistake one: undersized filters on the install

The first mistake is a filter that falls short of what the job calls for. ASHRAE recommends that mechanical filter efficiency be at least MERV 13 and preferably MERV 14 or better to help mitigate the transmission of infectious aerosols (AHRI). A filter rated below that recommendation is undersized against the guidance, and the sign-off record should show that the gap was known.

The catch is that the same source reports a constraint on the other side. Many existing HVAC systems were designed and installed to operate using MERV 6 to MERV 8 filters (AHRI). A crew told to upgrade to MERV 13 cannot simply drop a higher-rated filter into the existing setup and call the job finished. The job is finished when the system has been checked for the new filter.

That gives dispatchers two forms of the same mistake to watch for. One is a low-rated filter left in place on a job where the guidance calls for more. The other is a high-rated filter installed in a system built for MERV 6 to MERV 8 without a design check. Both leave a gap between what was promised and what was installed. The first gap is about filtration. The second is about whether the system can handle the load that a higher-rated filter adds.

For sign-off, the filter line on the work order should record three things: the rating installed, the rating the system was designed for, and whether the two were checked together. Recording the same three items on every job lets a team lead compare jobs quickly and spot a pattern, such as one crew repeatedly swapping in filters without a design check, before it turns into callbacks.

MERV ratings compared side by side

The three ratings that matter in this post sit on a clear line. The table compares them on the same measures: where the source places each rating, and the trade-off the source names for it.

RatingWhere the source places itTrade-off the source names
MERV 6 to MERV 8The range that many existing HVAC systems were designed and installed to use, which matches their original design (AHRI)No trade-off named for this range
MERV 13ASHRAE's recommended minimum (AHRI)Better at 0.3 to 1 micron particles, but the higher efficiency has a penalty (AHRI)
MERV 14 or betterASHRAE's preferred level (AHRI)Carries the same penalty as MERV 13 and greater (AHRI)

Read across the rows and the pattern is simple. The lower range is what many systems were built around. MERV 13 is the minimum that ASHRAE recommends, and MERV 14 or better is the preferred level (AHRI). Moving up the table buys better removal of particles in the 0.3 to 1 micron range, which the source says is the size of many virus particles, and it brings the penalty with it (AHRI). The sign-off decision is therefore not "higher is better." It is "higher, and checked against the system."

What higher filter efficiency costs

The source is direct that the gain is not free. It states that while MERV 13 and greater filters are better at removing particles in the 0.3 micron to 1 micron diameter size, the size of many virus particles, the higher efficiency does not come without a penalty (AHRI). The penalty is named as a cost and left unlisted in the quoted text, so the team should treat it as something to check on the specific job rather than a detail to skip.

On a sign-off, the practical meaning is this. The source names a penalty for higher-rated filters without specifying what it is, so that penalty belongs on the sign-off record. The penalty therefore belongs on the install side of the record, not just the parts list. If the system was built for MERV 6 to MERV 8, as many existing systems were (AHRI), a higher-rated filter may push the system harder than its design assumed. That is a reason to confirm the design basis before the filter is signed off, not after the customer reports weak airflow.

This is also why the filter and the duct work belong on the same checklist. The next section covers the duct side of that same concern, where the sources give a specific loss figure.

Mistake two: poorly sealed ducts

The second mistake is a duct system that was not sealed well enough for the equipment it serves. ENERGY STAR tells homeowners to evaluate and ensure that they have a well-sealed duct system, and it states the cost plainly: poorly sealed duct systems can result in up to 30% loss in efficiency (ENERGY STAR). That is the same 30 percent number the source attaches to improper installation in general, so the duct figure uses the same number but is stated as its own ceiling.

MeasureImproper installationPoorly sealed ductsSource
Efficiency figureUp to 30 percent reductionUp to 30% lossENERGY STAR
What it measuresSystem efficiency reductionEfficiency lossENERGY STAR

The same sentence sets a second requirement. The duct system has to be able to provide sufficient air flow throughout the living space (ENERGY STAR). A duct that is tight at the unit but delivers weak airflow to some rooms still misses the goal the source describes, which is airflow across the whole living space, not only a clean connection at the equipment.

For a crew, the sealing check is physical and is easiest to do before the walls close and the ceilings go up. For a team lead, the question is whether the job record shows that sealing and airflow were evaluated, not just that the ducts were run. Dispatchers can help by putting a duct evaluation into the job scope, so it is not left to the end of a long day when the tech is tired and the customer is waiting to leave.

When a poorly sealed system is found after the job is closed, the fix costs more than the check would have. A duct evaluation written into the scope at dispatch is a low-cost control, and it can catch the kind of efficiency loss the source describes before it reaches the customer's bill.

Installation standards to require from the contractor

ENERGY STAR gives the sign-off team a direct request to make. It advises homeowners to ask their HVAC contractor about high efficiency system options and to ensure the contractor uses the latest design and installation standards, which the source names as ACCA Manuals J & S, and Standard 5 (ENERGY STAR). The same request works for a company that hands installs to customers, because it sets the baseline the work is judged against.

In practice, the named standards map onto the two mistakes above. In this post's reading, the design side relates to the filter question, because it concerns whether the system was matched to the job. The installation side answers the sealing question, because it is about how the work is done. Treat the full set as the baseline for both mistakes, rather than picking the standard that fits the job at hand.

Three requirements follow for sign-off. First, the job record should state which standards the crew used. Second, it should name the design basis the system was matched to, including the filter rating it was designed for. Third, the record should confirm the latest versions of those standards were used, since the source asks for the latest standards, and an older practice does not meet that request.

Team leads and the sign-off checklist

A sign-off is only useful if the checks behind it are the same from job to job. SMACNA's homepage describes a program that will equip current and emerging field leaders with practical skills needed to manage projects effectively (SMACNA). For a dispatcher or team lead, that means turning install quality into a defined list of checks rather than leaving it to memory at the end of a long day.

For the two mistakes in this post, the list needs four items. The first is the filter rating installed, compared against ASHRAE's recommendation of MERV 13 at minimum and preferably MERV 14 or better (AHRI). The second is the design basis, meaning whether the system was built for the MERV 6 to MERV 8 range that many existing systems were designed and installed to use (AHRI). The third is a duct sealing and airflow check, because poorly sealed ducts can result in up to a 30% loss in efficiency (ENERGY STAR). The fourth is the installation standards the crew used.

A team lead should be able to read the record and see whether each item was checked, not only whether the job closed. Give every item a line with a result, and treat a blank as an open question. Blank fields are easy to sign past, and a visible "not checked" is easier to follow up than a silent gap.

Worked example: adding up the efficiency loss

Suppose a job has both problems: a filter the system was not designed for, and a duct system that is not well sealed. It is tempting to add the two figures and report a large loss. The sources do not support that. ENERGY STAR gives a ceiling of up to 30 percent for improper installation in general (ENERGY STAR), and a separate ceiling of up to 30% for poorly sealed duct systems (ENERGY STAR). Neither source gives a combined number, so the sign-off record should not stack them.

Cause named in the sourceFigure givenWhat the figure measures
Improper installationUp to 30 percentReduction in system efficiency
Poorly sealed duct systemUp to 30%Loss in efficiency
Average household energy billAbout $1,900 a yearTotal energy costs, with nearly half going to heating and cooling

The table shows the figures as the source states them, not as a sum. The $1,900 figure gives the scale of household spending, and the 30 percent figures describe efficiency. The words "up to" matter. They mark a ceiling, not an expected result for every job. The honest record therefore states what was checked and what was found on this job, such as a sealing test result or an airflow observation. It should not promise a specific percentage the sources never give.

Which one should you pick?

The sources do not name a single product to choose, so the pick depends on the design basis. The useful question is which option the system can carry while meeting the guidance. The table compares the options the sources support.

OptionWhat it addressesTrade-off the source names
Keep a MERV 6 to MERV 8 filterMatches the range many existing systems were designed and installed to use (AHRI)Gives up the better removal of particles in the 0.3 to 1 micron range that MERV 13 and greater provide (AHRI)
Upgrade to MERV 13 after a design checkMeets ASHRAE's recommended minimum (AHRI)Higher efficiency comes with a penalty the source names (AHRI)
Upgrade to MERV 14 or better after a design checkMeets ASHRAE's preferred level (AHRI)Carries the same penalty as MERV 13 and greater (AHRI)

Duct sealing is not a filter alternative. It is a separate check that sits alongside whichever filter option is chosen. A sensible pick is the option the design basis supports, plus a sealed and airflow-tested duct system (ENERGY STAR). If the guidance calls for MERV 13 and the system was built for a lower range, the record should show the design check and the decision that followed, rather than a filter swap with no review.

Steps to take before you sign off

Work through these steps in order before the paperwork goes to the customer. Steps 1 to 4 map to quotes in this post; step 5 is a recording step.

  1. Confirm the design basis. Check whether the system was designed for the filter range being installed. The source notes that many existing systems were designed for MERV 6 to MERV 8 (AHRI).
  2. Record the filter rating. Write down the rating installed and compare it with ASHRAE's recommendation of MERV 13 at minimum, preferably MERV 14 or better (AHRI).
  3. Confirm the standards. Ask the contractor to use the latest design and installation standards, named by ENERGY STAR as ACCA Manuals J & S and Standard 5 (ENERGY STAR).
  4. Evaluate the duct system. Confirm it is well sealed and able to provide sufficient airflow throughout the living space (ENERGY STAR).
  5. Record the results. Note the sealing and airflow findings on the job record, including any item that could not be checked.

Dispatchers can help by adding steps 3 and 4 to the job scope at booking. That way the checks are planned before the crew arrives, not squeezed in at the end.

Who this advice does not apply to

This advice is written for residential installs of the kind the ENERGY STAR page describes, where the goal is an efficient, well-sealed system that serves the household. It does not cover every commercial or specialized setting, and the sources here do not address those.

The filter section also does not apply to every system. The source says that many existing HVAC systems were designed and installed to use MERV 6 to MERV 8 filters (AHRI). The word "many" means not all. A system with a documented design basis that already covers the filter being installed still needs that basis confirmed and recorded, so the check becomes a quick confirmation. The source also does not say how to size a system for a higher filter, so that calculation belongs to the contractor and the design standards named in the post.

Related guides: Avoidable truck rolls: 3 dispatch mistakes to fix · Core body 37°C: 2 heat-loss facts for crew briefs · Perimeter measurement: 3 mistakes that skew runs.

Reader questions

How much do households spend on energy? ENERGY STAR says the average household spends about $1,900 a year on energy bills, with nearly half going to heating and cooling (ENERGY STAR). That heating and cooling share is the part an install affects most directly.

Does improper installation always cut efficiency by 30 percent? No. The source says improper installation can reduce system efficiency by up to 30 percent (ENERGY STAR). "Up to" is a ceiling, so the actual loss on a given job can be smaller.

Can an install also shorten equipment life? The source says improper installation can cost more on utility bills and possibly shorten the equipment's life (ENERGY STAR). The word "possibly" means the outcome is not guaranteed.

Can I just install a higher MERV filter? Not without a design check. ASHRAE recommends MERV 13 at minimum, but many existing systems were designed for MERV 6 to MERV 8, and higher-rated filters carry a penalty the source names (AHRI).

How much can poorly sealed ducts cost in efficiency? ENERGY STAR says poorly sealed duct systems can result in up to a 30% loss in efficiency (ENERGY STAR). As with the installation figure, this is a ceiling.

Who should check the duct system? ENERGY STAR tells homeowners to evaluate and ensure they have a well-sealed duct system that provides sufficient airflow throughout the living space (ENERGY STAR). For your team, the practical answer is that the job record should show that the check was done, by whoever owns the install.

What standards should I ask the contractor about? Ask the contractor to use the latest design and installation standards, which ENERGY STAR names as ACCA Manuals J & S and Standard 5 (ENERGY STAR).

Sources

More field guides