Straight into the service manual page
WrenchQuarry
More

Scaffolding closer than 4 m to a line: when to isolate

WrenchQuarry Editorial Team · Published · 13 min read · How these guides are written

Start with the distance, not the ladder

Isolation is needed when scaffolding or another temporary structure would come closer than 4 m to a low voltage line without written owner consent. A call that looks simple from the driveway can turn risky once a tech is on the roof or standing beside a yard fence. Overhead lines are easy to stop seeing. They run above gutters, over equipment storage, across parking lots and along boundary fences, and they are often at a height that hides them behind the very structures we are asked to work on. Before a job is booked, someone needs to ask one question: how close will anyone, or anything they carry, get to the line?

This post is for the people who make that decision before the van leaves: owners who price and schedule work, dispatchers who assign techs, and team leads who sign off on the plan. It is not a substitute for your local electrical safety rules or for the guidance your utility publishes. It is a practical checklist for the moments when a job near a line is about to be treated as routine.

Key takeaways

  • Identify the line before anyone plans the work.
  • Read the 4 m figure as a trigger for a decision, not a target, and remember it comes from guidance on low voltage lines.
  • Ask the network owner early about isolation.
  • Do not rely on gloves or rubber boots.
  • Write the plan down and make stopping easy.

The 4 m figure in one guide

The most specific distance figure here comes from WorkSafe New Zealand, in its guide on working near low voltage overhead electric lines. The guide says: "If written consent has not been obtained from the property owner then the power must be isolated if scaffolding or any other temporary structure needs to be closer than 4 m to the line."

Read that carefully. The sentence sets a distance, 4 m, and a condition: unless the property owner has given written consent. It does not say that work at or beyond 4 m is automatically safe, and it does not describe how to plan the work once the power is isolated. Treat it as a trigger for a decision, and record that decision in the job plan. The guide is also about low voltage lines, so do not assume the same figure applies to every line on every site. Check the guidance from the utility that owns the line in front of you.

Know which line you are dealing with

Before you can plan distance, you have to identify the line. Look for poles, crossarms, insulators and conductors. Note whether the line runs over the roof, along the yard boundary, across a gateway or over a laydown area. Ask the owner about service connections that are not obvious from the street. A line that feeds the building next door can still cross the corner of your job.

Take photos from more than one angle and add them to the job notes. Mark the approximate position of the line on a site sketch. If nobody on the team can tell whether a line is energized, treat it as energized until someone with the right authority confirms otherwise. Judging by the age of the pole or the color of the wire is not a method.

Related guides: Job cost sheet: 3 cost lines to total on every job · Apply 8 safety checks before dispatching for hot work.

Ask the right questions before the call

Most of the information you need can be gathered from a phone call before anyone travels. Ask the customer or property manager where the overhead lines run, whether they know who owns them, and whether any work has already been done near them. Ask whether the building has a scaffold, a lift, or a temporary platform already in place. Ask whether there are gates, fences, or trees that might hide a line from the street.

Then ask the questions that shape the method. Will the tech need to carry long material across the yard? Will a crane, a boom lift or a roll-off truck be needed? Is there a permanent work area, such as a loading bay or plant pad, that sits under the line? Each answer changes the distance picture. Write the answers in the job notes so the tech sees them before arriving, not after. For the form itself, see Field Service Work Order Checklist for Dispatch Handoffs.

Who decides when power is isolated

A tech on a roof cannot isolate a line by switching something off in the building. The line belongs to a network owner or utility, and switching it off is usually their decision. That owner is also the right contact for questions about whether a line has been made dead or is safe to approach.

For owners and team leads, this means the isolation request has to start early. Find the contact details before the job is booked. Ask how long a request usually takes, and build that time into the schedule. Do not promise a customer a start date that depends on a line being switched off until you have a confirmed isolation time.

When isolation is the answer

Isolation is the right answer when the work cannot be kept far enough from the line by other means. The same thinking should be applied to ladders, elevating platforms, lifting gear and long poles, because each one extends a person's reach.

Isolation also makes sense when getting the distance wrong would be costly and the work is slow or awkward. If a job needs someone to lean, reach or carry long material for an hour beside a line, that is a strong reason to ask for the line to be made dead first. Convenience for the crew is not a reason to accept closer working.

What a good isolation request looks like

A useful request says which line, which span or pole if known, which building or structure, the work to be done, the dates and hours needed, and who on site will be the contact. It also says what the team will do if the isolation is delayed or canceled. Do not send a vague message such as "we need the power off at the house." Vague requests produce vague answers, and the tech may end up working on a line that is still live.

Ask the network owner to confirm the isolation in writing, including the time it starts and the time it ends, and whether the line will be grounded. Confirm the arrangement again on the morning of the job. Plans change, and a confirmation from last week may not reflect today's switching.

Illustrative example: a yard wall job

A dispatcher books a crew to erect scaffolding along a yard wall. The plan would bring the scaffold closer than 4 m to a low voltage line, and the property owner has not given written consent. The team asks the network owner to isolate the line for a 10-hour window and to confirm it in writing. The tech checks the confirmation again on the morning of the job, and work starts only after that check.

Rooftop work near lines

The roof is often the closest place a tech can get to a line, and the work on it tends to involve moving around, carrying materials and using tools that can slip. Aerials, gutters, solar arrays and air conditioning units are all close to the airspace above a building, and it is easy to miss where a line passes over the parapet.

Plan the rooftop route before anyone climbs. Mark where the line sits relative to the access point, the walkway, the work area and the materials staging. If a ladder has to pass near a line to reach the roof, that belongs in the distance question too. A photograph is a poor judge of distance, because a lens flattens depth, so measure or estimate from the ground with the team present.

Any scaffold or temporary structure on a rooftop job that would come closer than 4 m to a low voltage line falls under the WorkSafe point above. Unless the property owner has given written consent, that structure means the power must be isolated. Make that check part of the scope, not a surprise on the day.

Yard work: vehicles, cranes and reach

Yards bring a different set of risks. Trucks, dumpsters, mobile cranes, telehandlers and tall loads all have heights that change during the day. A driver may judge a vehicle clear of a line when the load is down, then forget that a dump body or crane boom will rise. Dispatch should ask about vehicle types and the tallest equipment on the job before the tech arrives. See Verify overhead line clearance: 4 checks before dispatch.

Yard access points deserve special attention. The UK's Health and Safety Executive (HSE) notes that where field work is taking place it may be impractical to erect barriers and goal posts around overhead lines, and that these are more appropriate at gateways, on tracks and at access points to farm yards. Use that as a prompt. Where the route in and out of a yard passes under or beside a line, decide early whether the access itself needs a physical control.

Barriers, hoardings and boundaries

Physical controls are among the most useful tools in the planning kit, but they must suit the site. WorkSafe New Zealand says hoardings or enclosures can be installed on scaffolding to stop workers, or anything they hold or are attached to, from coming closer than the minimum approach distance. That is a useful example of a control built into the structure itself, rather than a sign taped to a fence.

HSE makes a related point: in some cases you may need a suitable combination of measures, particularly where overhead lines pass over permanent work areas. One barrier rarely covers every scenario. Combine a clear boundary, a written route and a dispatch rule that stops the tech working past it.

The same WorkSafe guide says its scaffolding figure is not intended to provide technical specifications for erecting scaffolding, because it is not possible to show all details. Treat any sketch in a job pack the same way. It is a prompt for proper design by a competent person, not a build drawing.

Insulation is not distance

Insulation helps, but it does not license closer working. WorkSafe New Zealand says insulated mats should comply with AS 4202, which signals that mats are a specified product, not something improvised from a van. An old rubber mat may look the part and still fail to meet the standard the guide cites.

The guide also says that, as well as the insulation options in its section 5, using non-conductive scaffolding or insulated elevating work platforms can help to minimise risk. The word to notice is "minimise." These measures reduce risk. They do not remove the need for distance planning or, where the rule applies, isolation.

The HSE is blunt on this point: "Don't rely on gloves or rubber boots to protect you." Treat them as the last layer of a plan, never the first. A tech who believes boots will keep them safe near a line has misunderstood the job.

A planning checklist for owners and team leads

Start with the facts: where the line is, its height where known, how far it is from the planned work, and whether the owner has consented in writing to any structure closer than 4 m to a low voltage line. For other lines, check the owning utility's guidance. Then decide the method. Can the job be done from the ground, or from a platform kept clear of the line? Or does it need isolation before anyone starts?

Next, write the controls down: boundaries, hoardings, insulated equipment that meets the relevant standard, a marked route, a spotter where the work needs one, and the name of the person who will confirm any isolation. A plan that lives only in someone's memory is a weak plan.

Finally, record who approved the plan and when. That record protects the tech, the owner and the business. If the plan changes on the day, because a truck is in the wrong place or a customer wants a taller structure, stop and update the plan before the change goes ahead.

What dispatchers should say to techs

Dispatchers often make the first decision without realizing it. The way a job is assigned matters. Tell the tech that the job is near an overhead line, what kind of line it is if known, what distance is known, and whether isolation has been confirmed. If it has not, the tech should not start the part of the work that brings them close.

Give techs permission to stop. A tech who feels pressure to climb or reach closer to a line because a customer is waiting is in the wrong position, and the schedule put them there. Build a rule that a job near a line pauses until the plan is confirmed, and make sure every tech knows the rule before they leave the depot.

What owners should put in writing

For owners, the most useful habit is a short written note. Record the line's position, the work zone, the distance, the consent status and the isolation arrangement. Put the name and contact details of the person who confirmed the isolation with the note, and keep it with the job ticket.

Plan for contact and emergencies

Even a careful plan can fail, so the team should know what to do if something goes wrong. Before work starts, make sure the lead has the emergency number for the local emergency services and the contact number for the line owner. Put both on the job sheet, not only in a phone. Agree who calls, who keeps others away from the area, and who stays with any injured person.

Common mistakes

Some mistakes repeat across jobs. The first is treating an overhead line as background. Once a tech is on site and the line has been there for years, it can disappear from the plan. The second is confusing "I can reach it" with "it is safe to reach." The third is relying on a photo to judge distance. The fourth is assuming that because the utility has visited before, nothing has changed. Lines get rerouted, poles get replaced and temporary structures get added.

When to stop and ask

If you are not sure whether a task will bring anyone or anything inside the safe distance, stop and ask. That includes whether a crane boom will swing, whether a platform will be raised in the wrong place, or whether a truck will need to be parked under a line. A short delay costs little compared with a contact.

Overhead lines stay where they are, but the work around them changes. A rooftop job becomes a yard job, a ladder becomes a platform, and a quick check becomes a long day. The owners, dispatchers and team leads who plan for distance before the van leaves are the ones who keep their people out of the line's reach. If a job could bring a scaffold or other temporary structure closer than 4 m to a low voltage line, the isolation question is already on the table unless the owner has consented in writing.

Next step for today

Today, pick the next booked job near a line and mark the line's approximate position on a site sketch, along with the work zone and the distance from the planned work. Send that sketch to the team lead before the van leaves.

Frequently asked questions

Who decides whether a line is switched off?

Does insulation allow closer working? No. Insulation helps reduce risk, but it does not remove the need for distance planning or, where the rule applies, isolation.

Sources

More field guides