Straight into the service manual page
WrenchQuarry
More

Servicing moving machines: 3 duties before crews start

WrenchQuarry Editorial Team · Published · 11 min read · How these guides are written

Before servicing a machine that can move, three duties apply: control and prove energy, set movement rules, and keep a qualified person at the controls.

Key takeaways

  • Control every energy source: isolate, lock, tag with a name and reason, then verify by trying the start control and watching that nothing moves
  • Set rules for movement: the default is no movement while anyone is inside the guarded zone; if movement is required, use extension tools or other means to minimize the hazard
  • Keep the operating station under the control of a qualified operator or craftsman at all times, including brief runs, inching moves and test cycles
  • Keep everyone beyond the reach of machine elements that may move rapidly and present a hazard
  • Run a pre-job brief on site before tools come out: walk the machine, name each energy source, say who locks what, mark the reach line, confirm who holds the station

The three duties, plainly

These duties come from California’s control-of-hazardous-energy rule for cleaning, repairing, servicing, setting-up and adjusting work on prime movers, machinery and equipment (California Code of Regulations, Title 8, Section 3314). If your crews work in California, this rule is your floor. If they work elsewhere, it is still the clearest checklist you will find on this job. Your own state may add steps. Ask your safety officer or counsel which ones.

Why this matters for you as an owner or dispatcher: the crew you send is walking into a machine that can move without them. A service call is the exact moment when the machine is most likely to be opened, jammed, cleaned or adjusted. That is when energy is present, guards are off and hands go where they should not. Your dispatch note is the last control you hold before they arrive.

What “unjamming” counts as

The rule treats unjamming as part of the work. Cleaning, repairing, servicing and adjusting activities include unjamming prime movers, machinery and equipment. That means a quick pull on a stuck part is a servicing task. It earns the same lockout, the same verification and the same checks as a full repair.

Tell your crews this in plain words: if it is stuck, it is a service task. Nobody clears a jam by hand just because the repair tech has not been called yet.


Duty one: control the energy and prove it

Lock out, tag out, verify

The first duty is controlling hazardous energy before the first tool comes out. You isolate every source. You lock it. You tag it with a name and a reason. Then you verify. Verification is not a glance at the switch. Try the start control. Watch that nothing moves. Confirm gauges read zero or safe.

A crew locks the disconnect, skips the test and reaches in. If the wrong breaker was thrown, the machine is live. Your dispatch checklist should force a spoken verification: who locked it, what was tested, and what was seen. For the full list of lockout checks, see Lockout checks before equipment is opened: 6.

Keep the lock in one person’s hands. The person who applies the lock removes it. Never let a supervisor take a crew member’s lock off to save time. If that person leaves the site, the lock stays until a documented transfer of control happens.

Scope: what counts as this work

The rule covers cleaning, repairing, servicing, setting-up and adjusting operations on prime movers, machinery and equipment. Field crews often hear “repair” and think only of a major fix. Setting up a machine for a new run counts. Adjusting a sensor counts. Cleaning a chute counts.

Your dispatch notes should say which of these the crew is doing. A note that says “look at conveyor” is too vague to drive a safety plan. A note that says “clean and adjust the infeed rollers” tells the crew to plan for full energy control.

Where the crew must stand

The rule requires all participants to be beyond the reach of machine elements which may move rapidly and present a hazard to them. In your own words: nobody’s hands, tool or body can be inside the zone where a fast-moving part would strike.

Walk the machine with the crew before they touch it. Mark the reach line on the floor with tape if you can. If a task cannot be done outside that line, the task needs a different plan. More on that plan below.


Duty two: set the rules for movement during the task

The normal rule: no movement while anyone is in the zone

The default is simple. The machine does not move while anyone is inside the guarded zone or doing work where movement could injure them. Energy stays controlled. Guards stay where they belong.

Some jobs cannot be done this way. Some adjustments need the machine to run. Some cleaning requires a slow crawl. The rule gives you a path for that, and it comes with two conditions.

The exception: movement is allowed under two conditions

First, if the machinery or equipment must be capable of movement during this period in order to perform the specific task, the employer shall minimize the hazard by providing and requiring the use of extension tools (eg., extended swabs, brushes, scrapers) or other methods or means to protect employees from injury due to such movement.

Second, the operating station where the machine may be activated must at all times be under the control of a qualified operator or craftsman.

Here is how this compares when a task must involve movement:

SituationWhat the rule requiresCrew position
Task can be done with energy offControl energy, verify zero, no movementOutside the reach line
Task requires machine movementExtension tools or other means to minimize the hazardBeyond the reach of fast-moving elements
Who holds the controls during movementQualified operator or craftsman, at all timesAt the operating station only

Do not read that table as a menu you can pick from on site. The first row is the default.

Extension tools are a real requirement

“Extension tools” is not a suggestion. If the task needs movement, you provide extended swabs, brushes, scrapers or other means, and you require their use. A rag on a stick is a start. A purpose-built tool that keeps hands outside the reach line is better.

Ask your crew lead to list the extension tools for each machine in your service book. Do that before the next call, not during it.

The qualified operator or craftsman

The person at the station must be a qualified operator or craftsman. Not whoever happens to be closest. Not a helper who has seen the job twice.

For you as a dispatcher, this changes scheduling. If the only qualified operator on site is the one doing the hands-on task, you cannot also assign them to hold the station. Send a second qualified person, or change the plan.

Working at height often comes with this kind of work. Roofs, mezzanines and platforms put your crew above a machine that can still move below them. WorkSafe New Zealand publishes a range of guidance on working safely at height, including their working-at-height topic page. If your crew works on platforms, pull that guidance into the same pre-job brief.


Duty three: keep the operating station under control

Who is allowed to run the machine during service

The station that can start the machine stays with a qualified operator or craftsman for the whole task. That includes brief runs, inching moves and test cycles. If the qualified person steps away, the machine stops and stays stopped.

Write this into the dispatch note: name of the qualified operator at the station, name of the person at the task, and what happens if either leaves. When the note carries names, the rule becomes enforceable on site.

Everyone else stays out of reach

The second half of the control duty protects the rest of the crew. Everyone beyond the reach line. No hands near a part that can move quickly. No leaning in to watch.

If a second person must observe, they stand where they cannot be struck. Tape the line. Say it out loud. A quick verbal check before the first move helps prevent close calls.

Hand signals and one voice

Movement runs on one voice or one set of signals. Pick one.

In practice this means the person at the task says “clear” before a move. The person at the station says “moving” and then “stopped.” Short phrases. No shouting over running plant.


Training your crew before they touch the machine

Who can train on the job, and when

Your crew will not all arrive with the same skills. California’s powered industrial truck rule puts it this way: on-the-job training is allowed only where such operation does not endanger the trainee or other employees (California Code of Regulations, Title 8, Section 3668). If a trainee cannot perform the task safely, they watch. They do not practice on a live machine.

What trainees do while they wait

A trainee who cannot operate safely still has work. They can hold the tag, call out the checks, keep the reach line clear or run the log. Give them a real role so they do not drift into the zone.

On your first pass through a new site, pair the trainee with the qualified operator. The trainee reads the procedure aloud. The operator confirms each step. That builds the habit you need on every later call. For what to capture in the training file, see Powered truck operator training records: 4 required fields.

One exempt type of work

The powered industrial truck training rule carries one carve-out. Agricultural operations as defined in Section 3437 of the General Industry Safety Orders are exempt from the requirements of Section 3668.

If your crews service machines on farms, note the exemption. It changes the training rule for powered industrial trucks on those sites.


How to fold this into your dispatch

What the dispatch note must carry

Your dispatch note is the last thing your crew reads before they roll. Give it five lines every time: machine name and model, energy sources present, whether movement is required for the task, the name of the qualified operator at the station, and the location of the reach line. For a fuller dispatch form, see Field Service Work Order Checklist for Dispatch Handoffs.

That note turns a vague call into a plan. It also gives you a record if something goes wrong. Keep the notes for at least as long as your state requires for safety records, and ask your counsel how long that is.

The pre-job brief on site

When the crew arrives, the lead runs a brief before tools come out. Walk the machine. Name each energy source. Say who locks what. Mark the reach line. Confirm who holds the station. Confirm whether movement is needed, and if so, which extension tools are on the truck.

Keep the brief under ten minutes. Short briefs get done. Long ones get skipped.

Checking the machine still matches the plan

Machines change. Someone adds a bypass. Someone tapes over a sensor. Before the first lockout, your lead checks that the disconnects and controls still match the note.

If the machine no longer matches, stop. Re-walk it. Update the note. Send the update to the office so the next crew does not inherit the same surprise.


Illustrative example: cleaning a conveyor infeed

A three-crew outfit sends a two-person team to clean and adjust the infeed rollers on a conveyor. On arrival, the lead walks the machine with the operator. They isolate the main disconnect and the control-circuit source, lock each, tag each with a name, then verify by trying the start control and watching for movement.

The team marks the reach line where a fast-moving roller would strike a hand. The clean requires the belt to creep so residue comes off the far side. Because movement is needed, they lay out extended brushes and scrapers on the belt guard. The qualified operator takes the station. The second person stands outside the line with a brush on a long handle. The cleaner calls “clear,” the operator calls “moving,” then “stopped.” After the last pass, the cleaners step back outside the reach line, and each person removes only the lock they applied.

Next step today: copy the short checklist below into your dispatch form, and run it on your next call.


Questions owners ask

Do these duties apply if I am not in California? The duties themselves are a sound practice anywhere. The specific text above comes from California’s rule. Your state may word it differently or add steps. Ask your safety officer or counsel which version applies where your crews work.

What if only one qualified person is on site? Then you cannot hold the station and do the task at the same time. Change the plan so movement is not needed, or send a second qualified person. Do not let a helper take the station.

How do I prove the trainee rule was followed? Keep the training record with dates, the tasks the trainee performed, and the name of the person who judged them safe to work. That record answers the question after the fact.

What counts as an extension tool? Anything that keeps hands outside the reach line while the machine moves: extended swabs, brushes, scrapers, or a purpose-built handle. If your crew jury-rigs one on site, that is a sign your service book needs a real tool listed for that machine.

Who removes the lock? The person who applied it. If that person leaves the site, follow your documented transfer of control. Never let a supervisor remove a crew member’s lock to save time.

What does the agricultural exemption cover? It exempts qualifying agricultural operations from the powered industrial truck training requirements.


Before the next call: a short checklist

Energy: every source isolated, locked, tagged and verified by a test.

Movement: default is no movement; if the task needs movement, extension tools or other means are on the truck and required.

Station: a named qualified operator or craftsman holds the controls the whole time.

Reach line: marked, spoken and respected by everyone on site.

Trainee: given a role outside the zone, or kept off the machine until safe.

Brief: five lines in the note, ten minutes on site, update sent back to the office.

Run that list on your next three calls. Then sit with your crew leads and mark the steps that were hardest to follow. Those are the ones to fix first.

Sources

More field guides