Straight into the service manual page
WrenchQuarry
More

Work above a crew: 3 Oregon and Washington duties

WrenchQuarry Editorial Team · Published · 12 min read · How these guides are written

Work above a crew carries three duties in Oregon and Washington: know who holds competent person roles, protect workers below, and plan the way down. Each duty comes from a clear rule you can read yourself.

Key takeaways

  • Oregon competent person roles: Oregon describes a competent person for fall protection (Division 3, Subdivision M) and a competent person for scaffolding (Division 3, Subdivision L).
  • Oregon hoisting restriction: Oregon OSHA does not accept the provisions described under ANSI Z133-2017, section 5.7.11 as a way to hoist personnel. Build your lift plan around another method.
  • Washington protection for workers below: Under WAC 296-155-035, subsection (5), where work is in progress above workers you must provide a catch platform or other means to protect those working below.
  • Washington structural security: Subsection (8) requires you to secure or brace component parts of structures as construction progresses to prevent collapse or failure.
  • Washington removal plan: Subsection (9) requires prompt and safe removal of injured employees from elevated work locations, trenches, and excavations prior to commencement of work.

When you stand at the tailgate and hand out assignments, you are deciding who climbs, who works below, and who waits. You are also deciding which state rules apply. Oregon and Washington both set rules for construction work, but they write them in different places and in different words.

This post walks through three duties you carry when your crew works above someone else. The first comes from Oregon's fall protection rules on ladders and scaffolds. The second comes from Washington's rules on protecting workers below. The third comes from Washington's requirement that you plan how an injured worker gets down.

The reader for this post is an owner, dispatcher, or team lead who writes the day's assignments. You pick who goes on the roof, who runs the ladder, and who sorts materials at ground level. You make that call before the first truck rolls.

Oregon competent person roles

Oregon draws a line around the role of the competent person in fall protection.

Oregon Occupational Safety and Health describes the role in its fall protection topic page. The page "Describes a competent person for fall protection in construction activities and explains the requirements in Division 3, Subdivision M that apply to them."

The same page draws a second line for scaffolding. It "Describes a competent person for scaffolding in construction activities and explains the requirements in Division 3, Subdivision L that apply to them."

So Oregon describes the role in two places. One description covers fall protection generally. Another covers scaffolding. Either way, the crew needs to know who holds each role.

Oregon's fall protection page also covers the rules that touch ladders and scaffolds directly. The page "Covers the requirements in Division 3, Subdivision M, Fall Protection and highlights fall protection requirements for work on ladders and scaffolds."

Read that last sentence again. Ladder work and scaffold work both fall inside Subdivision M's fall protection rules in Oregon. That means you cannot treat a ladder as a tool outside the fall protection plan. The plan has to reach the ladder.

There is one more item on that page worth your attention. Oregon OSHA states plainly how it treats a particular hoisting method. The page "Describes how Oregon OSHA does not consider the provisions described under ANSI Z133-2017, section 5.7.11, as an acceptable means or method to hoist personnel."

In your own words on the tailgate: do not plan to move a person up or down using the method described in that ANSI section. Oregon has said it will not accept it. Write the lift plan around another method and brief the crew on it.

What this means for your assignment sheet

Before the first truck leaves, three questions should have answers on your sheet:

  • Who holds the competent person role for fall protection today?
  • Who holds the competent person role for scaffolding today?
  • What method will move people, and is it one Oregon accepts?

Write the names next to the job on a field service work order checklist. Tell the crew at the tailgate. A name on a sheet that nobody reads does not help anyone on the roof.

Side-by-side: where the two states write the rules

The two states place these duties in different documents.

DutyState and sourceWhere it lives
Competent person for fall protectionOregon, Oregon Occupational Safety and HealthDivision 3, Subdivision M
Competent person for scaffoldingOregon, Oregon Occupational Safety and HealthDivision 3, Subdivision L
Ladder and scaffold fall protection requirementsOregon, Oregon Occupational Safety and HealthDivision 3, Subdivision M
Personnel hoisting method not acceptedOregon, Oregon Occupational Safety and HealthANSI Z133-2017, section 5.7.11
Protection for workers belowWashington, WAC 296-155-035Subsection (5)
Secure or brace as work progressesWashington, WAC 296-155-035Subsection (8)
Prompt and safe removal of injured employeesWashington, WAC 296-155-035Subsection (9)

Use this as a lookup when you write the day's plan. Oregon work points you at the fall protection page. Washington work points you at the cited WAC section.

The duty to protect the crew below

The second duty is the one you meet on a real job. Someone is on the roof. Someone else is at ground level. Work is in progress above the people below.

Washington writes this requirement directly. WAC 296-155-035, subsection (5), states: "(5) Where work is in progress above workers, you must provide a catch platform or other means to protect those working below."

Put in your own words: when work happens above your crew, you owe the people underneath a way to stay safe. The rule names a catch platform first. It also allows other means. You pick the method that fits the job, and you brief the crew on it before work starts.

This duty lands on you as the dispatcher. You know who is on the roof and who is sorting materials below. The assignment sheet should show both. If the sheet has names above and names below, you need a line that says how the people below are protected.

A catch platform is one answer. A controlled drop zone with barriers is another. Roping off the area so nobody walks under the work is another. The rule does not pick for you. It requires that you pick something and put it in place.

Think about how this plays out on a gutter job. Two workers are on the roof pulling old sections. One worker is on the ground cutting new stock. Old fasteners and hand tools coming down from the roof land above the ground worker's head. Cut pieces stay at ground level. Your protection plan has to exist before the first cut.

The same duty reaches scaffold work. When your scaffold crew works above a ground crew, the people below need the same cover. The catch platform or other means applies whenever work is in progress above workers, not only on a roof.

There is a related requirement in the same Washington section that pairs with this one. Subsection (8) states: "(8) As construction progresses, you must secure or brace the component parts of structures to prevent collapse or failure."

Read together, subsections (5) and (8) cover two directions. Subsection (5) protects the people below from what falls. Subsection (8) keeps the structure itself from coming apart as work moves along. Both belong in your plan for any Washington job where the structure is being changed.

Writing the below-work plan

Before the crew leaves the yard, write four things on the sheet for any Washington job with work above:

  • Who is working below, by name
  • What protects them, named in plain words
  • Who sets that protection in place, by name
  • How the structure is secured or braced as work progresses

That last line is easy to skip. A structure that is fine at the start of the shift can be a different structure by lunch. Subsection (8) asks you to keep it secure as construction progresses. Check it at each break, not just at the start.

The duty to plan the way down

The third duty shows up on your worst day. Someone gets hurt on the roof, in the trench, or on the scaffold. The injured worker is elevated, and work is still going on around them.

Washington covers this in WAC 296-155-035, subsection (9). It reads: "(9) You must ensure prompt and safe removal of injured employees from elevated work locations, trenches and excavations prior to commencement of work."

In plain words: you plan the way down before the work starts. The rule says prompt and safe. It also says prior to commencement of work, which means the plan exists before the first task of the day, not after the injury.

This is the duty that separates a good dispatcher from a reactive one. A worker hurt on a roof needs a different answer than "call for help and wait."

Your removal plan answers four questions:

  • How does an injured worker get off the roof or out of the excavation?
  • Who performs that removal?
  • What equipment stays on site for it?
  • Who calls for help, and when?

Write the answers on the sheet for every elevated or excavated job. Review them at the tailgate. If the plan needs a piece of equipment that is not on the truck, fix the truck before you leave.

The rule covers elevated work locations, trenches, and excavations. A roof job and a trench job both need the same plan. Your crew might run a ladder one day and a deep excavation the next. The duty does not change with the task.

How the plan holds up under pressure

A removal plan written in a hurry fails. A removal plan written in the yard and reviewed at the tailgate holds up. Build yours around what you actually have on the truck.

Walk the equipment list with your leads. Confirm that whatever the plan calls for rides on the truck every day, not just on the days you expect trouble. Trouble does not send a heads-up.

Brief the plan at the tailgate in one short paragraph. Name the person who performs the removal. Name the person who calls. Confirm the route off the roof or out of the trench. Then start work.

Putting the three duties together on one sheet

The three duties share a pattern. Each one asks you to decide something before the crew moves. Each one puts the decision in writing. Each one gets spoken at the tailgate.

The competent person duty asks you to identify who holds each role. The below-work duty asks you to name protections. The removal duty asks you to name a route. Names, protections, and routes belong on the sheet in that order.

Run the sheet this way for a typical day:

  • Note who holds the competent person role for fall protection and the one for scaffolding
  • List who works above and who works below
  • Name the catch platform or other means for the people below
  • Confirm how the structure is secured or braced as work moves along
  • Write the removal route and the person who performs it
  • Note any personnel hoisting method, and confirm Oregon accepts it

That last line matters for Oregon jobs.

Illustrative example: one sheet for a roof day

Three workers: two on the roof pulling old sections, and one on the ground cutting new stock. The sheet names all three, lists the catch platform that protects the ground worker, and names the person who performs a removal and the route off the roof. The lead checks each line at the tailgate before the first ladder goes up.

A day where all three duties bite at once

Picture a Washington re-roof with a ground crew. Two workers are on the roof. One worker is sorting materials below. The structure is open where old decking came out.

Your sheet names the ground worker and the catch platform that protects them. It also names who sets that protection in place and who checks it.

As the tear-off moves along, the crew opens more of the deck. Subsection (8) asks you to keep the component parts secure as construction progresses. Your lead checks the bracing at the first break and again at lunch.

Then a worker slips at the roof edge. The plan from subsection (9) takes over. The named person performs the removal. The route off the roof was briefed that morning. Nobody has to invent a method while a worker waits.

That is what these three duties look like on a real day. None of them is dramatic on paper. All of them matter when the day turns.

Take this step today

Common questions owners ask

Do these duties apply to every job my crews run?

The Oregon duties on competent persons, ladders, and scaffolds live in the fall protection rules for construction activities. The Washington duties in the cited section apply where that section applies to your work. Read the sections linked above and match them to the work your crews actually perform.

Where does Oregon set out the scaffolding competent person?

The Oregon fall protection page sets out that role under Division 3, Subdivision L.

What counts as "other means" under Washington's protection for workers below?

Any method you choose that protects the people below and fits the job. Put it in place and brief the crew on it at the tailgate.

Does the removal duty cover a ladder fall at ground level?

Subsection (9) names elevated work locations, trenches, and excavations. A fall at ground level is a different situation. Plan the way down for every job that puts a worker up high or down in the ground.

How does the Oregon hoisting restriction affect my lift plan?

Check the lift plan against the restriction above. Change any plan that relies on the ANSI method before the next Oregon job.

What should I do first if I am not sure a duty applies to my crew?

Start with the source you are reading. Oregon rules are on the fall protection page from Oregon Occupational Safety and Health, and Washington rules are in the cited WAC section. Check it before the crew leaves the yard, not after an inspection.

Before the trucks roll

Three duties carry the day when your crew works above someone else. Know who holds the competent person roles in Oregon, including scaffolding. Protect the people below in Washington with a catch platform or other means. Plan the prompt and safe removal of an injured worker before work starts.

Write them on the sheet. Speak them at the tailgate. Confirm the equipment that backs them up is on the truck. Then send the crew out with the answers already in hand.

Sources

More field guides